| by Kenneth Chase | 47 comments

Apartment Renovation Ep.1 / How to lay Laminate Flooring


I’ve spent the past few days doing some renovations in this small apartment. For now I’ve installed the laminate flooring and I’m about to finish placing the doors. This is the first video in a series of five or six where I’ll show you how to lay down the laminate flooring. First of all, I’ve made a design with an online app to allocate the space and see what the apartment will look like in the end. This is the floor plan of the apartment, where we can see its distribution. You can see the living room, the kitchen, the bathroom, and the two bedrooms. By dragging this blue point we can move around the interior of the design with this 3D view. We can also select a view of the inside at eye level. These types of apps are very useful to visualize our projects, and creating walls and furniture is quite easy. Laying laminate flooring is a relatively simple task, especially if the floor is perfectly level and in good condition. There are levelling compounds that can be used in extreme cases, but that’s not the case here. First we must remove all the bits of cement or glue from the corners and the floor itself, as well as cleaning the entire surface. After cleaning, I’ll place underlayment on the floor. We needn’t cover the entire floor at once. In order to avoid breaking it, I’ll keep adding strips as needed. For best results, the underlayment should go 2 cm up the walls. This kind of underlayment is good for keeping moisture away, as well as making up for imperfections on the floor. This is the flooring I’m going to install. It’s gray and has saw cuts imitating oak grain. As you might know, this kind of flooring has an anchoring system to attach the boards to one another. In order to get it as close to the wall as possible, I’m going to cut the male anchors on all the sides that touch the wall with the laminate cutter, leaving the female side oriented towards us so that we can continue placing the rest of the boards. I place some 9mm wood blocks to act as spacers in order to avoid problems due to the expansion of the flooring. In order to fasten the boards to one another, we must raise and tilt the board we are going to insert, and then bring it down while pushing towards the other board. If all goes well, the anchoring system itself will join the two pieces together until you can barely see where they’re connected. In order to measure the last piece, we only have to turn it and mark it, leaving the same separation to the wall because of expansion. As you can see, this kind of laminate cutter is quite easy to use, and we’ll avoid leaving too much dust at home. It is advisable that the last board is no shorter than 20 centimetres, you can cut the first board as much as necessary to avoid this problem. In the next row, we can start with the remaining part of the piece we cut before. It’s important that the joints don’t match. The next boards are more complicated to place, because we have to attach two anchorages rather than one. There are several methods, but what I usually do is anchor the longest side by tilting the boards a little like before. Now I’ll use this tapping block, which you can easily find in hardware stores. It has a part made of rubber with a rebate to avoid damaging the boards when pushing them into the previous board. By doing this, you may move the previous row, which is why it’s important to keep placing spacers between the flooring and the wall. In order to place the last board of the next rows, I’ll use this steel pull bar I made. They’re also easy to find in hardware stores. We place the strips of underlayment required, and following the same steps we can easily do most of the rest of the room if there aren’t many corners or doors in your room. This underlayment has self-adhesive tape to join the parts together, if yours doesn’t have it, you can use masking tape instead, making sure the strips don’t overlap. Here’s the first setback. I have to measure the gap between the board and this chest-high wall, minus the space for expansion. In this case I’ll use a jigsaw to cut as required. As a rule of thumb, the flooring has to be laid in the same direction as the main light source in the house, usually the windows, but it’s not a problem if you want it to face a different direction. The same thing happens here. After measuring, I place the board as before. I’ll leave the required space for a door bar between the flooring and the bathroom floor. I’ve also left an 8mm gap between the flooring and the door frame, which will be covered by the jamb and casing. In my case, the front door has already been installed, and at the bottom of it I left a gap for the flooring, so this time I’ll start laying the flooring the other way around, because otherwise it would be impossible to slide the last board under the door. It’s not the best option, but it’s not a problem if you have to lay a few floorboards like this. I remove the sliding door protections and continue placing the floorboards. Since this is a small apartment, I’m going to try placing the floorboards in one piece without door bars under the doors. It goes a little over the recommended length, but I’ve left a gap big enough because of expansion, so it should be okay. I prefer the look of the flooring without the door bars. It also makes cleaning the house easier! In order to do that, I measure the required cuts, leaving the same gap in all directions to account for expansion, including door frames. In the bedrooms I have to do the same as before. I’ve had to cut the first board with the measurements I got from the board that goes under the door. Now all that’s left is to install the plinth. I’ve thought about bringing along my Portable Workshop, which I think will be quite useful to finish the renovation. To cut the plinth I’ll use a sliding miter saw and an tool-actuated vacuum. It will switch itself on whenever I turn on the saw, making the job much easier. First I cut the left over underlayment, at the same height as the flooring. There are plinths with the same color as the flooring, but in this case I went with waterproof lacquered DM. Now I’ll start installing the plinth on one corner, making a miter joint. We can trim the corner in the back a little so that it matches the wall better. I cut the other end of the joint straight, but it can also be cut at an angle. I apply some anchoring adhesive. It’s a dense product that dries fast, which locks the plinth onto the wall. I also apply some adhesive on the plinth joints. We could use steel nails in the uneven parts of the wall, if there are any. Drive them into the plinth and cover the hole with white wax. There are many ways to finish the plinth pieces that touch the casings. This is what I do: I cut the plinth part at a 45 degree angle, then I grab another leftover piece of plinth and cut it at 45 degrees, and then straight, with the same thickness as the plinth itself. I use cyanoacrylate with accelerator to glue the pieces together. In order to improve the bond, you can use a very thin file. This way I can cover the head of the plinth with the same material. Another method would be to paint it white. There’s another problem that can come up. I need a very thin piece of laminate flooring to cover a gap. I cut it in the portable workshop, and remove part of the anchoring system so that I can attach it from above, and glue it to the previous piece with cyanoacrylate. In the areas where the plinth doesn’t go well on the wall because it’s too uneven, it’s advisable not to force the plinth too much. Before applying the last coat of paint on the walls, we can fill these gaps with plaster and sand them, so that we can paint over them later. If the floor is uneven, you may have to trim the plinth a little, and some joints are best glued before putting them on the wall, such as in this case. Lastly, I’ll place this L-shaped steel profile to finish the area by the stairs. I drill and the concrete plate and screw in the L-shaped piece, pushing it down. I haven’t shown you how to place the plinth pieces that touch the casings of the bedroom doors and the built-in wardrobes, which I’ll lay in the next video, where I’ll also show you how to install the doors themselves. See you soon!

47 Comments

Paoson WoodWorking

Nov 11, 2018, 12:54 pm Reply

If you'd like to help me, you can upload subtitles in your own language following this link:
http://www.youtube.com/timedtext_video?ref=share&v=8QVskPnkI3A
Puedes contribuir con subtítulos en tu idioma en el siguiente enlace:

nilson patricio

Dec 12, 2018, 4:21 pm Reply

muito bom o trabalho,parabéns.

Sergey Soldatov

Dec 12, 2018, 4:35 pm Reply

Тhe name of the program? (3D) Thank you in advance.

Максим Мороз

Dec 12, 2018, 4:43 pm Reply

Все супер!

Ксюха 100

Dec 12, 2018, 4:49 pm Reply

It's not difficult work, but very interesting just you doing it.
Have waiting next about doors. Thx!

Criart Tub

Dec 12, 2018, 4:50 pm Reply

Nice vídeo amigo

katana24

Dec 12, 2018, 4:53 pm Reply

Joder, ha quedado de lujo, yo instalé hace 15 años dos habitaciones con mi padre y nos quedó bien, pero no tan bien como le ha quedado a usted.

Clive Bashford

Dec 12, 2018, 4:53 pm Reply

The best laminate floor laying video I've seen. Learned a lot from this. Many thanks.

Hans Matz Weisse Feder

Dec 12, 2018, 4:54 pm Reply

perfekt exzellent – grüße vom federl. ????

Николай Ситков

Dec 12, 2018, 5:00 pm Reply

Не очень метод, после такого заколачивания замки не держат и ламинат "разъезжается".

PRANEET BANE – WoodWorking Machines

Dec 12, 2018, 5:11 pm Reply

Nice work ????

ToolsConsumables

Dec 12, 2018, 5:13 pm Reply

Dear Sir,
This is an exceedingly clean & very professional job. I cannot wait to see the remainder of this project. Very well done. Kind regards.

Борис Мартынцев

Dec 12, 2018, 5:46 pm Reply

Professional approach.

Tchello Silveira

Dec 12, 2018, 6:16 pm Reply

Incredible knife, there is no such model in Brazil, we usually use miter saw. I liked yours because it is easy to use and it does not make a noise.

John Coloe

Dec 12, 2018, 6:28 pm Reply

You're a very accomplished woodworker and I highly respect your work. However, I'd like to offer a bit of feedback.

Firstly, inside joints should always be butt joints. External joints are all that are mitered. The reason? So end grain doesn't show. Just as in cabinetry and furniture.

Secondly, finishing a run of trim is called a return and you finished yours correctly. You also created the wraparound correctly, although all three sides are sometimes built on the bench, depending on length/awkwardness.

Lastly, casings, jambs, etc. are cut exactly using s piece of flooring as a guide for an oscillating tool. Perfect results everytime.

Looking forward to future apartment renovation videos.

IMEDA MAMALADZE

Dec 12, 2018, 6:47 pm Reply

SUPER!NO COMENT!

Bulete Aurelian

Dec 12, 2018, 6:53 pm Reply

Interesting. i'll be keeping a close eye on this series.

Mikhandmaker

Dec 12, 2018, 7:31 pm Reply

Nice job mate, very clean 😉

Mark Dalton

Dec 12, 2018, 7:46 pm Reply

A nice neat job. I'm doing something similar in a couple of weeks. Thanks for the tips. I like the way you finished the skirting boards up to the door architrave. It gives it a very professional look. ??

Luis Angel Diaz

Dec 12, 2018, 8:02 pm Reply

Buen trabajo gracias por tus aportes un saludo desde Argentina

Ferenc Szabó

Dec 12, 2018, 8:07 pm Reply

Good to see you kept and use the mobile workstation 😉

Juliano Vicente

Dec 12, 2018, 8:19 pm Reply

Top?

Mr. T Oliver

Dec 12, 2018, 10:02 pm Reply

Great job dude ??☀️

DIY Random Project

Dec 12, 2018, 10:14 pm Reply

Muy didáctico. Es un vídeo que recomendaré en tienda a mis clientes. Pero, me a faltado algo. Donde está el Portable workshop ?

Me Dicen Peter

Dec 12, 2018, 11:54 pm Reply

Perro paoson que usa pistolas de calafetar de Truper

Sergio Pellacani

Dec 12, 2018, 12:19 am Reply

Good work

Глеб Ерохин

Dec 12, 2018, 12:24 am Reply

my life will not be the same, cutter for laminate floring.

Humus Workshop

Dec 12, 2018, 12:48 am Reply

Super neat as usual, nice project!

Manuel garcia franco

Dec 12, 2018, 1:01 am Reply

Te ha quedado de lujo el suelo, muy bueno el truco del canto para que no se vea el el dm en el final del zocalo, me lo apunto. Saludos.

Daniel Monares

Dec 12, 2018, 1:24 am Reply

Hola. Mucha suerte con esta nueva serie de videos. Soy un seguidor de tu trabajo. Aprovecho de preguntarte sobre la posibilidad de vitrificar este tipo de pisos. De antemano gracias.

M M

Dec 12, 2018, 1:29 am Reply

How to expense square feet

Nicolás Salgado

Dec 12, 2018, 1:44 am Reply

I wish i have seen this last year, before installing all my house flooring! Coom tips and good info. Thanks

Arturo vidaña

Dec 12, 2018, 2:29 am Reply

Una muuuy buena chamba te aventaste! Felicidades!!!!

Dessert Man

Dec 12, 2018, 3:38 am Reply

Great work?????

HASANKHON HABIBOV

Dec 12, 2018, 5:35 am Reply

Непаниатно пачиму по штучни ложет а нелзя один полос одновремино ??

Jörgen Börg

Dec 12, 2018, 9:03 am Reply

some really nice tips, my friend! too bad i already finished my flooring

HODYO Design

Dec 12, 2018, 1:03 pm Reply

Looking forward to the next episodes! From what I've seen at 0:27, you didn't caulk the baseboards and the trims yet. I assume you'll do that and the touch-ups as well once you're done…

Francesco Zampieri

Dec 12, 2018, 2:06 pm Reply

Can I ask you the name of the app you used to design the apartment?
Thanks a lot

Making HUERTAS Stuff

Dec 12, 2018, 7:26 pm Reply

Great job mate 🙂

Neil F

Dec 12, 2018, 6:29 am Reply

Hi. I love your last project, the blade and bit sharpening jig. Is it possible to purchse a printed copy of the plans? I don't have a computer and printer. Just a cell phone. Please let me know? Thank you.

Dieter Büngers

Dec 12, 2018, 7:44 pm Reply

Mal wieder eine Handwerklich gute Arbeit ???????

Joe G.P.

Dec 12, 2018, 10:16 am Reply

2:10 you are cutting the wrong side, as proof see 2:30

Paulo Monti

Dec 12, 2018, 6:21 am Reply

Show! 🙂 o/

zieglernr2

Jan 1, 2019, 11:35 am Reply

I really like these videos, they are easy to understand and the recording quality is great.
I was thinking that, it most be a pain for you, to stop every 2 mins or so, to replace the camera.

When I have said that, I can't argue with the results.

Miguel Camarero

Mar 3, 2019, 8:23 pm Reply

Hola, el piso es madera?

Антончик Таратутов

Jul 7, 2019, 2:22 pm Reply

За торец крашенного плинтуса мега респект))

Roman Gubanov

Aug 8, 2019, 9:41 pm Reply

Awesome job! My advise to all the comrades enjoying doing the renovation by themselves – do measure the geometry of your rooms before starting. More often than not the opposite walls are not parallel and adjuscent walls are not square to each other. This will force you to make non-square cuts if you lay laminate in one piece across the whole appartment.

Leave a Reply