Заусенцы!Аппаратный Маникюр/Мои Новые Фрезы!
Hello everyone! Each of us faced the problem of burrs. This is a break in the skin The main reason for the appearance of burrs is dry skin which occurs upon frequent contact with water, household cleaning, as well as in the wind, and frost. If you do not cut the burr in time, then a piece of skin is ride up more and more gradually opening the bleeding wound. Infection or microbes that cause inflammation can easily get into it. On these hands all the wounds have dried up, and my task is to put them in order, give them well-groomed appearance as much as possible, and most importantly not to harm. I am pushing the cuticles away by the pusher and I am starting the hardware manicure. Today I am working with HD Freza brand cutters. HD Freza brand cutters. Here are my favorite cutters and burs This is a bullet “flame” and balls of different sizes and abrasiveness, as well as the cutter for removing material and for grinding the skin. HD Freza is produced in Russia, Poland, Germany, the USA, and Switzerland, as well as in Hong Kong, but the cutters produced in Hong Kong are different from other mills in terms of abrasiveness. It should be borne in mind that Hong Kong has a green notch like our blue, a blue notch like our red, and a red notch like our yellow. Therefore when ordering cutters be careful! Today I will need 2 burs (cutters). This is the flame with the blue notch of 1.8 mm in diameter and a ball with the red notch of 2.9 mm in diameter. These cutters and burs can be purchased at the Myslitsky Nail online store. All the links I will leave in the description under the video. And also for all my subscribers, the store provided a 5% discount on the Nata5 promotional code. Myslitsky Nail is a representative of such major brands as H D Freza cutter and Mühle Maniküre, as well as a large selection of tools and equipment for nail care. Little by little, I am beginning to work
by flames. The cutter is rotating in the direction of reverse, the speed as usual is an average of 15.000 revolutions. I am cleaning off the pterygium, and I am carefully processing the side rollers and sinuses of the nail on the right with this cutter. Step by step, I am removing all dry skin. I am not staying in one place, the movements should be intermittent so as not to burn the client. Then I am switching the reverse direction to “forward”, and I am processing the sinuses and rollers o left n the. Then I am polishing the side rollers with a ball, as well as I am cleaning, and I am polishing the cuticle. I am trying not to touch the nail by the cutter. Then I am degreasing the nails, and I am applying the primer. I am strengthening the nails today with the rubber base Uno Strong, I am carefully rubbing the thin layer into the nail, and I am adding a sm all drop of the base to make the alignment. I am turning the finger over, and I am drying it … The design will be very simple and very fast, I am painting all the nails with pink gel polish. I am leaving the holes but you do not need to try and draw them, I am painting all 4 nails at once, , and the big one separately. I am drying the first layer, I am applying the second layer, and I am drying. I am removing the sticky layer. But I need to make the sticky layer only in the area of the hole, s o I am applying the thin layer of the base with the brush. By the way, this little By the way, this little dot on the nameless n a il is the foil, I just tried to make the design on the primer first, but I couldn’t, so I am redoing it. I am drying for 30-40 seconds and I am printing the foil in the area of the hole on all the nails at once. This design is good in that when it grows, it will look very harmonious. Then I am putting the top without a sticky layer… and the manicure is ready! And let’s remember what the hands looked like before the manicure… now they look like this. Girls, who like my manicure put your fingers up and subscribe to my channel if you came for the first time, and I say goodbye until the next release,
bye for now …))